Rising DampCan occur in any season, not just during the rainy season, because whenever moisture creeps close to the walls of the house, this problem can arise. Before mold starts to appear, let’s learn how to solve the issue of rising damp together!
What causes rising damp?
Rising damp occurs due to the accumulation of moisture at the lower walls or areas close to the ground. The moisture can come from various sources, such as moisture from the soil, groundwater seeping up the walls, rain splash, watering plants, building houses near water sources, water pooling, or poor drainage systems.
The moisture accumulated at the lower part of the house will cause the paint film to lose its adhesion to the wall surface, leading to paint blistering and peeling, followed by mold or black stains, musty odors inside the house, and some structural deterioration over time. Homeowners should address this issue promptly.
How to solve rising damp
Managing the problem of rising damp should start with surface preparation, removing mold, and then applying a primer and topcoat as needed, following these steps:
1. Prepare the surface properly
First, scrape off the blistered and peeling paint film using a metal scraper, and sand off the first 2-3 feet of the paint film completely (down to the bare concrete) with sandpaper.
2. Remove mold and algae
If the concrete surface has mold or algae stains, apply a mold and algae remover, Beger MouldFree M-001, in one coat without rinsing off. Wait until it is completely dry before proceeding to the next step.
Beger MouldFree M-001
- Removes mold and algae down to the roots
- The solution penetrates deep beneath the surface, protecting it from mold for a long time
- Water-based formula, non-irritating scent, safe for users and residents
- Can be left on without rinsing, helping to reduce work steps
3. Apply moisture-proofing agent
Next, apply a moisture-proof primer for concrete with a maximum moisture resistance of 35%, Beger Water Block W-010, in 1-2 coats, applying it up to about 60-100 centimeters along the groove line.
Beger Water Block W-010
- Prevents moisture up to over 35%
- Prevents the growth of mold, algae, salt stains, and efflorescence in concrete walls
- Protects the lower part of the house or the lower areas of buildings from groundwater
- Enhances the adhesion of the primer and topcoat, eliminating premature peeling of the paint film. Apply 1-2 coats on the concrete wall where the first 2-3 feet of paint has been removed, allowing it to penetrate into the plaster. . . Leave it for 2-3 hours.
4. Apply primer
Apply the multipurpose primer paint with moisture resistance up to 75%, Beger Water Block Primer B-3100 (Beger Water Block Primer B-3100) oil-based formula. Allow it to dry for at least 4-6 hours before applying the topcoat in the next round.
Beger Water Block Primer B-3100
- Mix well and use immediately, or you can mix with Beger Thinner M-15 up to 5%.
- Resistant to external moisture up to 75%, can be applied immediately after rain.
- Can be applied on new plaster, old plaster, fresh plaster, and wet plaster surfaces.
- The breathable paint film helps prevent blistering and peeling issues.
- The white paint film helps cover surfaces and allows for easy checking of the work.
- Helps prevent efflorescence, salt stains from plaster, mold, and algae.
- Suitable for plaster walls, concrete walls, plastered brick walls, precast concrete, and fiber cement boards.
5. Apply the topcoat
Apply the topcoat with Beger exterior or interior paint that meets the desired specifications in 1-2 coats, such as BegerCool UV Shield exterior and interior paint, BegerCool 2in1 exterior and interior paint with built-in primer formula, or BegerShield AirFresh Gold Ion interior paint.
BegerCool UV Shield
- Reflects heat over 94.2%, saving up to 25% on electricity.
- Perfectly reflects UV rays that damage homes across all wavelengths (UVA, UVB, and UVC).
- Keeps your home looking clean and new with Advanced Nano Silicone Technology.
- The breathable paint film prevents water from seeping into the walls with Cross Link Technology.
- Prevents paint film peeling, protecting your home for over 15 years.
- Prevents mold and algae, resistant to alkaline from plaster.
- Does not contain mercury or lead.
BegerCool 2in1
- Saves x2 by saving both time and paint + labor costs up to 5,370 THB (based on labor cost of 20 THB/coat/sq.m.).
- Surface Lock technology enhances penetration, reinforcing adhesion between the film layers and surfaces deeply.
- Smooth & Clean technology provides a beautiful, smooth film that withstands scrubbing over 250,000 times and is easy to clean even with a matte finish.
- Eco-friendly paint innovation helps reduce greenhouse gas emissions by up to 144,414 gCO2.
BegerShield AirFresh Gold Ion
- The most trusted interior paint by mothers and children, guaranteed with the Best Interior Paint award from the Asianparent Awards 2023
- Gold Ion technology helps inhibit the coronavirus (SARS-CoV-2)*, bacteria, and fungi on walls
- Mild scent ready to move in within 5 minutes (after the paint dries)*, with formaldehyde levels below and no harmful volatile substances
- 3D cleaning performance, purifying air, easy to wipe clean, and withstands scrubbing up to 400,000 times*
If you have questions about using Beger products, including primer, multipurpose undercoat, topcoat, and issues with dampness in the lower part of the house, you can consult experts from Beger directly at Line: @begerpaint during business hours
